5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup

5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup

5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup
In 1 Heat Press Machine =. + 2x plate press machine. (12.5cm/15cm) + 1x Cap Mat Press (8x15cm). This 5-in-1 heat press machine can transfer colorful pictures and characters (via sublimation ink/pigment ink and sublimation paper/heat transfer paper) onto ceramics, glasses and textiles such as polyester, cotton, flax, chemical fiber etc. It can be used for T-shirts, mouse mats, jigsaw puzzles, door hangers, ceramic tiles, ID badges, coasters, floor mats and just about every other in flat surface. Time control range: 0-999 Sec. Temperature error band: +/-5 degrees.

Heater size for t shirt: 2938 / 3838cm. Heater size for mug: 11oz cone.

Heater size for plate: 12.5cm, 15cm. Heater size for cap: 815cm. Be sure to operate with a safe.

Please turn the machine off. Er when the machine is on. Temperature is still high after turning it off. Keep out of the reach of children.

The data above is for reference only, the exact time and temperature. Would depend on the material you use and your intended goals. Pressure knob for t shirt heater, cap heater, plate heater. Pressure knob for mug heater.

You can use the pressure knob to adjust the pressure, turning it clockwise will increase the pressure. Please pull the handle up and press it down to see whether the pressure is suitable (before starting the intended operations). Setting the Time & Temperature. Celsius degree indicator light (when this light up, it means you are using Celsius degree meter). Fahrenheit degree indicator light (when this light up, it means you are using Fahrenheit degree meter). Press "OK" button, panel shows P-1, press to set the temperature. After setting temperature, press "OK" button again, panel shows P-2, press to set the time. Press OK button for 3 seconds to save the temperature and time. Machine starts to heat up automatically. You can press to set temperature deviation (please do not set temperature deviation without technicians support). When reach to target temperature, press. Button, machine will countdown automatically. On the sublimation paper with. (except dark color cotton used heat transfer paper). Do not use the sublimation paper. Preparing the sublimation blank e. Prepare the t shirt, place it on the t shirt heater. Should lie on the board.

When reach to the target temperature, place the sublimation paper with the printed side downward facing the t shirt. Press the heater down to start printing. THE TIMER WILL START WORKING AUTOMATICLY and countdown after heater down. Countdowns to zero and the buzzer rings, please.

Up to open the t shirt heater. And then take out the. T shirt and paper carefully. And you will see the. Image is well pressed on the mug.

Be careful of the hot heating surface. Please make sure the heating temperature and transfer time are correct. In order to extend the service life. Please turn the machine off for 15 minutes after.

Using it continuously for 4 hours. To determine the suitable temperature and time according to the material. The heater will take some time to warm up to reach the target temperature f. COMMON PRINTING FAILURES and THEIR POSSIBLE REASONS.

The color is lighter: the temperature is too low; OR the pressure is not even; OR the time is too short. The design is indistinct: the time is too long which led to ink diffusion. The design has no luster: the pressure is too high; OR the temperature is too high.

Part of design is indistinct: heat printing zone OR the heating is not even. Scar on design: heat printing time is too long. Depth of color is not the same: pressure not even OR the coating is not even. Paper stick to the object: the temperature is too high; OR the coating of the object is not good. Lease do not set the temperature.

Will shorten the service life of the machine. 1 X Fully-assembled machine with platen press. 1 X Removable silicone pad and cotton pad (Due to batch issues, you may receive red or blue, but the quality is exactly the same). T-shirts, cups and hats are NOT included. The item "5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup" is in sale since Friday, August 2, 2019.

This item is in the category "Business & Industrial\Printing & Graphic Arts\Screen & Specialty Printing\Heat Transfer\Presses". The seller is "colorsub" and is located in Walnut, California.

This item can be shipped to United States, all countries in Europe, Canada, Mexico, Japan, Brazil, Australia.


5 in 1 Combo Heat Press Machine Digital 15x15in for T-shirt Mugs Plate Hats Cup


Digital Printing Equipment   Map   Contact   Privacy Policy   Terms of Use